Highlights
  • Supports USB Super-Speed/High-Speed/Full-Speed
  • Provides Backup button
  • DC Power Input: Big IDE 4-pin DC Power Connector
Introduction

U3-SATA201 is USB 3.0 to SATA II (3Gb/s) Bridge Board. It has an USB SuperSpeed device port and a SATA II (3Gbps) host port.

U3-SATA201 translates the communication protocol between SATA II (3Gb/s) and SuperSpeed USB commands.
Supports the USB Mass Storage Class Bulk-Only Transport Specification.

U3-SATA201 provides the perfect solution for data backup and transferring of data between computers using SATA drives.
Technical Specifications

USB to SATA Bridge Board

  • USB 3.0:
    • Complies with USB 3.0 Specification, USB Mass Storage Class, Bulk-Only Transport Specification
    • Supports USB Super-Speed/High-Speed/Full-Speed Operation
    • Supports USB HID operation
    • Supports USB2.0/USB3.0 power saving mode
    • Supports external SPI NVRAM for Vendor VID/PID of USB2.0/USB3.0 device controller
  • Serial ATA:
    • Complies with Gen2i/Gen2m of Serial ATA II Electrical Specification 2.6
    • Supports SATA II Asynchronous Signal Recovery (Hot Plug) feature
    • U3-SATA201-PM supports SATA Port Multiplier. (Note: Support IOI SPM393/393PS/394 only )
  • LEDs:
    • Provides Power and Disk Access Indicator LEDs
    • Provides USB 2.0 Link/ACT Indicator LED
    • Provides USB 3.0 Link/ACT Indicator LED
  • Provides backup button
  • DC Power Input:
    • Big IDE 4-pin DC Power Connector
Software
  • Supports FNet PCClone EX Lite Backup software
  • Supports FNet TurboHDD USB software to improve USB performance
Available Models

U3-SATA201-7
With standard firmware

U3-SATA201-PM
With Firmware supports SATA PM

U3-SATA201-22
With standard firmware
Physical Dimensions
  • U3-SATA201-7: 83.3mm x 21.56mm x 38.6mm
  • U3-SATA201-PM: 83.3mm x 21.56mm x 38.6mm
  • U3-SATA201-22 : 83.3mm x 21.56mm x 44.1mm
  • SCSI 1 50pin Low Density Centronics Connector Form Factor. (Fit to most standard SCSI enclosure)
Net Weight
  • U3-SATA201-7: 38.2g
  • U3-SATA201-PM: 38.2g
  • U3-SATA201-22 : 39.3g
Hardware Requirements
  • Desktop PC: with either a built-in USB (1.0 or 2.0 or 3.0) controller or an USB (1.0 or 2.0 or 3.0) to PCI Host Adapter equipped with an external USB port.
  • Laptop PC: with either a built-in USB (1.0 or 2.0 or 3.0) controller or an USB (1.0 or 2.0 or 3.0) to CardBus PC Card equipped with an external USB port.
Operating System Requirements

USB 2.0 :

  • Windows2000/XP/Vista/7, MAC 9.2 or later version.
    • No driver installation for Windows2000/XP/Vista/7, MAC 9.2 or later version

USB 3.0 :

  • Windows2000/XP/Vista/7, MAC 9.2 or later version.
    • Your Host need to support USB 3.0 Driver
Kit includes
  • U3-SATA201 Bridge Board
  • CD-tilte (Backup software & TurboHDD USB software)
  • User's Guide
Related Products
  • USB3-EXS-AB USB 3.0 A to B Type Cable
  • U3-PCIE1XG201 USB 3.0 to PCI Express Gen 2 Card
  • SPM393 One to Five SATA Port Multiplier RAID Controller
  • SPM393PS Two to Four RAID Controller with a port selector function
  • SPM394 One to Five SATA Port Multiplier RAID Controller with LCD Module